Eccentric Concentric Reducer Pipe Fittings , Threaded Sanitary Tri Clamp Fittings
Tri Clamp Eccentric reducers, as their name implies, reduce in diameter towards the center thus forming a conical cylinder. A concentric reducer is often used inline on a vertical flow application, or if laid horizontally, as an increaser. We do not recommend reducing in the horizontal as pooling may occur. In these cases, an eccentric reducer, which lays flat on one side is preferable. Concentric reducers have a lower chance of producing agitation like an end cap reducer may.
Eccentric reducer fitting to connect two pipes of different diameters that are along the DIFFERENT pipe axis
Fitting clamps to tubing on both ends for a non-permanent seal, providing take-down access
Stainless steel 316L for strength and greater ease in welding than 304-grade steel
Maximum operating pressure rating of 250 psi at 70 degrees F ambient temperature
Clamp eccentric reducer tri clamp sanitary fittings, body material sanitary stainless steel 316L/304, Surface finishing 180 Grit ID/ 150 Grit OD. Fits to Sanitary Stainless Steel Tubing and clamps onto tubing at both ends. It has a maximum operating pressure rating of 200 pounds per square inch (psi) at 70 degrees F ambient temperature. It is suitable for use in the food, beverage, biotech, pharmaceutical, and other sanitary process industries. When purchasing fittings, consider the application, as this will affect material type, shape, size, and required durability.
We manufacture T304 or T316L Sanitary Polish Triclamp Fittings found primarily in the Bakery, Beverage, Cosmetic, Dairy, Food or Pharmaceutical Industries. Our Sanitary Butt Weld Fittings can meet or exceed 3A/DIN/BPE/SMS etc standards with an ID polish of 180 Grit or 25 Ra on the Inside of the Tube and a 150 Grit or 32 Ra on the Outside of the tube. NEW TEK supplies each Sanitary Butt Weld product with the size and alloy and a heat number for full traceability for either alloy. Our Sanitary Butt Weld Fittings are made to close tolerances to permit easy and fast installation of a corrosion resistant, crevice free, fully sanitary process line. As a suggestion, you may wish to weld using the tungsten gas method for true fusion of wall to minimize pitting and thinning. Material test reports can be provided.
Welded Reducer No.RT0411012 |
Size |
L1 |
D |
D2 |
T |
DN20/15 |
7 |
22 |
18 |
1.5*1.5 |
DN25/20 |
11 |
28 |
22 |
1.5*1.5 |
DN32/20 |
22 |
34 |
22 |
1.5*1.5 |
DN32/25 |
11 |
34 |
28 |
1.5*1.5 |
DN40/20 |
33 |
40 |
22 |
1.5*1.5 |
DN40/25 |
22 |
40 |
28 |
1.5*1.5 |
DN40/32 |
11 |
40 |
34 |
1.5*1.5 |
DN50/25 |
44 |
52 |
28 |
1.5*1.5 |
DN50/32 |
33 |
52 |
34 |
1.5*1.5 |
DN50/40 |
22 |
52 |
40 |
1.5*1.5 |
DN65/25 |
73 |
70 |
28 |
2.0*1.5 |
DN65/32 |
62 |
70 |
34 |
2.0*1.5 |
DN65/40 |
51 |
70 |
40 |
2.0*1.5 |
DN65/50 |
29 |
70 |
52 |
2.0*1.5 |
DN80/40 |
78 |
85 |
40 |
2.0*1.5 |
DN80/50 |
56 |
85 |
52 |
2.0*1.5 |
DN80/65 |
27 |
85 |
70 |
2.0*2.0 |
DN100/50 |
90 |
104 |
52 |
2.0*1.5 |
DN100/65 |
61 |
104 |
70 |
2.0*2.0 |
DN100/80 |
34 |
104 |
85 |
2.0*2.0 |